The claimed characteristics of the materials sold by us may differ only for the better
Waterproofing of expansion joints
Bitumen-polymeric sealants of the following type are used to seal expansion joints, concrete joints of highways and airfields, as well as to remove cracks in road and airfield coatings: Bituminous polymer polymeric “Albizol” and Bitumen polymer polymeric Teknonikol No. 42.
The main difference between these sealants is the high adhesion properties, as well as resistance to high loads.
When sealing cracks on road and airfield surfaces, the use of ICBM mastics (bitumen-rubber mastic), mastic is also used when sealing expansion joints on the roadway and on bridge structures.
ICBM mastic hot application. Its main difference from other mastics is the addition of fine fractions of rubber and polymers to petroleum bitumen, high elasticity, the ability to apply these mastics in the winter season, as well as high adhesion and resistance to mechanical stress.
- You've just added this product to the cart:
Bitumen-polymer hermetic №42 (BP)
Read MoreБыстрый просмотрBitumen-polymer hermetic №42 (BP)
77.00 $ Retail price per kgUsage: Airport, Parking of cars, Reconstruction of roads, Strengthening of asphalt-concrete seam, Waterproofing of bridges, Waterproofing of expansion joints, Waterproofing of industrial seams, Waterproofing of road surfaces
Bitumen-polymer sealant Technonikol No. 42 is a one-component material consisting of oil bitumen, modified with rubber and technological additives. Available in three versions, depending on climatic zones: BP-G25, BP-G35, BP-G50. A sealant is used in road construction to seal expansion joints in highways, runways of aerodromes and highways.
The name of indicators Unit. measurements Value Test method BP-G25 BP-G35 BP-G50 Softening temperature, not lower than 0С 90 90 90 Flexibility on the rod Æ 20 mm, not higher 0С -25 -35 -50 Relative elongation at the moment of rupture, not less than at -20 ° C % 75 75 75 -||- Temperature of stickiness, not less than 0С 50 50 50 -||- Stamina, number of cycles, no less than – 30000 30000 30000 -||- Water absorption, not more than % 0,2 0,2 0,2 -||- Change in properties under UV irradiation, not more than ч 1000 1000 1000 -||- - You've just added this product to the cart:
Bituminous polymer polymeric Albizol (BP)
Read MoreБыстрый просмотрBituminous polymer polymeric Albizol (BP)
44.00 $ Retail price per kgUsage: Airport, Parking of cars, Reconstruction of roads, Strengthening of asphalt-concrete seam, Waterproofing of bridges, Waterproofing of expansion joints, Waterproofing of industrial seams, Waterproofing of road surfaces
Bituminous polymer polymeric Albizol (BP) – produced at the Kostroma waterproofing materials plant, is an improved and more inexpensive modification of the bituminous polymer sealant Technonikol (higher adhesion, higher softening point, more UV stabilizers). It is used to seal expansion joints, to rehabilitate temperature and strength cracks in cement concrete, asphalt and concrete and polymer-concrete coatings of roads, bridges, aerodromes (there is an experience of Albizol application both at civil airfields and military ones)
The name of indicators Unit. measurements Value BP-G25 BP-G35 BP-G50 Softening temperature, not lower than 0С 100 100 100 Flexibility on the rod Æ 20 mm, not higher 0С -25 -35 -50 Relative elongation at the moment of rupture, not less than at -20 ° C % 75 150 200 Temperature of stickiness, not less than 0С 50 50 50 Stamina, number of cycles, no less than – 30000 30000 30000 Water absorption, not more than % 0,5 0,5 0,5 Change in properties under UV irradiation, not more than h 1000 1000 1000 - You've just added this product to the cart:
Mastic Hot Bituminous Rubber MBR
Read MoreБыстрый просмотрMastic Hot Bituminous Rubber MBR
46.00 $ Retail price per kgUsage: Parking of cars, Strengthening of asphalt-concrete seam, Waterproofing of bridges, Waterproofing of expansion joints, Waterproofing of flat roofs, Waterproofing of foundations, Waterproofing of industrial seams, Waterproofing of road surfaces
Roofing mastic of hot application Eureka No. 41 is designed for effective repair and flat roofing, but can also be used for waterproofing steel structures, concrete blocks, columns, concrete building blocks and pipelines. The use of hot waterproof mastics is more effective and durable than the use of cold mastics because of the greater liquidity of the material
Indicator name Unit. measurements Normative value MBR-65 MBR-75 MBR-90 MBR-100 Softening temperature according to the KiS method, not less than оС 65 75 90 100 Depth of penetration of the needle at 25 оС, not less than 0,1 mm 40 30 20 15 -||- Растяжимость при 25 оС, не менее cm 4 4 3 2 -||- Водонасыщение за 24 ч, не более % 0,2 0,2 0,2 0,2 Application temperature, within 0С +5 to -30
+15 to -15
+35 to -5
От +40 to -5 – - You've just added this product to the cart:
Mastic hot bituminous-rubber MBR 75 ZKM
Read MoreБыстрый просмотрMastic hot bituminous-rubber MBR 75 ZKM
14.00 $ Retail price per kgUsage: Parking of cars, Strengthening of asphalt-concrete seam, Waterproofing of bridges, Waterproofing of expansion joints, Waterproofing of flat roofs, Waterproofing of foundations, Waterproofing of industrial seams, Waterproofing of road surfaces
Hot bitumen – rubber mastic consists of petroleum bitumen, rubber crumb and plasticizer with a softening temperature of 75 grains, produced at the Kostroma waterproofing materials plant, is an inexpensive analogue of MBM mastic from Technonikol. It is intended for the device of waterproofing and anticorrosion protection of underground pipelines, and also for sealing of cracks and seams on flat roofs. Available in several modifications, differing in density and strength characteristics.
Indicator name Unit. measurements Normative value MBR-75 Softening temperature according to the KiS method, not less than оС 75 Depth of penetration of the needle at 25 оС, not less than 0,1 mm 30 Extensibility at 25 оС, not less than см 4 Water saturation for 24 hours, no more than % 0,2 Application temperature, within 0С От +15 до -15
Waterbar DZ 160/50-6/35 (PVC)
1,254.00 $ Price per running meterUsage: Restoring the sealing of expansion joints, Waterproofing of expansion joints
Hydraulic Stem DZ 160 / 50-6 / 35 Aquastop (AquaBarrier), according to the classification of a waterproof dowel, designed to seal expansion joints in the construction of buried, hydraulic structures, as well as to restore the tightness of expansion joints in existing structures. 160 (mm) – height of hydrostar, 50 – width of expansion joint, 6 – number of anchors, last figure 35 – height of anchors.
Waterbar DZ-100/25-4/25 (EPDM)
1,104.00 $ Price per running meterUsage: Restoring the sealing of expansion joints, Waterproofing of expansion joints
Hydraulic dowel DZ 100 / 25-4 / 25 Aquastop (AquaBarrier), according to the classification of a waterproof dowel, designed to seal expansion joints in the construction of buried, hydraulic structures, as well as to restore the tightness of expansion joints in existing structures. 100 (mm) – the height of the hydrostar, 25 – the width of the expansion joint, 4- the number of anchors, the last digit of 25 – the height of the anchors.
Waterbar DZ-130/25-6/25 (EPDM)
1,293.00 $ Price per running meterUsage: Restoring the sealing of expansion joints, Waterproofing of expansion joints
Hydraulic Stem DZ-130 / 25-6 / 25 Aquastop (AquaBarrier) according to the classification of a waterproof dowel designed to seal expansion joints in the construction of buried, hydraulic structures, as well as to restore the tightness of expansion joints in existing structures. 130 (mm) – the height of the hydrostar, 25 – the width of the expansion joint, 6 – the number of anchors, the last digit of 25 – the height of the anchors.
Waterbar DZ-160/100-6/35 (PVC)
1,357.00 $ Price per running meterUsage: Restoring the sealing of expansion joints, Waterproofing of expansion joints
Hydraulic Stem DZ-160 / 100-6 / 35 Aquastop (AquaBarrier), according to the classification of hydro-shield, designed to seal expansion joints in the construction of buried, hydraulic structures, as well as to restore the tightness of expansion joints in existing structures. 160 (mm) – the height of the hydrostar, 100 – the width of the expansion joint, 6 – the number of anchors, the last figure 35 – the height of the anchors.
Waterbar DZ-160/20-6/35 (PVC)
1,192.00 $ Price per running meterUsage: Restoring the sealing of expansion joints, Waterproofing of expansion joints
Hydraulic Stem DZ-160 / 20-6 / 35 Aquastop (AquaBarrier), according to the classification of hydro-shield, designed to seal expansion joints in the construction of buried, hydraulic structures, as well as to restore the tightness of expansion joints in existing structures. 160 (mm) – the height of the hydrostar, 20 – the width of the expansion joint, 6 – the number of anchors, the last figure 35 – the height of the anchors.
Waterbar DZ-160/30-6/35 (PVC)
1,213.00 $ Price per running meterUsage: Restoring the sealing of expansion joints, Waterproofing of expansion joints
Hydraulic Stem DZ-160 / 30-6 / 35 Aquastop (AquaBarrier), according to the classification of hydro-shield, designed to seal expansion joints in the construction of buried, hydraulic structures, as well as to restore the tightness of expansion joints in existing structures. 160 (mm) – the height of the hydrostar, 30 – the width of the expansion joint, 6 – the number of anchors, the last figure of 35 – the height of the anchors.
Waterbar DZ-160/40-6/35 (PVC)
1,233.00 $ Price per running meterUsage: Restoring the sealing of expansion joints, Waterproofing of expansion joints
Hydraulic Stem DZ-160 / 40-6 / 35 Aquastop (AquaBarrier), according to the classification of hydro-shield, designed to seal expansion joints in the construction of buried, hydraulic structures, as well as to restore the tightness of expansion joints in existing structures. 160 (mm) – the height of the hydrostar, 30 – the width of the expansion joint, 6 – the number of anchors, the last figure of 35 – the height of the anchors.
Waterbar TARAKAN-120 (PVC)
1,215.00 $ Price per running meterUsage: Restoring the sealing of expansion joints, Waterproofing of expansion joints
Hydraulic Stem TARAKAN 120 Aquastop (AquaBarrier) – waterproofing key, designed to seal expansion joints during new construction, as well as to restore the tightness of existing expansion joints. The watercover of TARAKAN and polyvinylchloride is produced, 120 (mm) is the width of the waterstop, (6) is the number of anchors (fasteners in the kit), 45 (mm) is the distance between the anchors, and 20 (mm) is the width of the sealed expansion joint.
